HappyModel Crazybee Pro V3 F4 2-4S Flight Controller AIO Brushless Whoop Mobula7 Mobula7 HD

QAR 169,00

Mode:

Frsky

Flysky

Quantity

Featured Products

RadioMaster Bandit ExpressLRS 915MHz ELRS RF 1W Module TX

QAR 330,00 QAR 379,00

SUNLU PETG 3D Printer Filament 1.75mm 1KG

QAR 44,00 QAR 53,00

RadioMaster Bandit BR3 ExpressLRS 915MHz ELRS TCXO Receiver

QAR 95,00

RadioMaster TX16S Mark II Max Radio Controller Transmitter

QAR 880,00 QAR 1.078,00

RadioMaster Bandit Nano ExpressLRS 915MHz RF ELRS 1W Module TX

QAR 152,00 QAR 190,00

DOGCOM 5200mAh 6S 120C 22.2V LiPo Battery QS8 [DG]

QAR 308,00 QAR 440,00

HappyModel Crazybee Pro V3 F4 2-4S Flight Controller AIO Brushless Whoop Mobula7 Mobula7 HD

Notes:

The biggest differences between Crazybee F4 PRO V1.0, V2.0 and V3.0 are:

V2.0 could handle 1-3s Lipo/LiHV

V1.0 could handle only 1-2s Lipo/LiHV

V2.0 use bigger bind and boot button , change the BAT/GND pad to “through hole”

V3.0 supports 2S – 4S LiPo, ESC upgraded to 10A. A few things have gone back to how it was before due to the lack of space: no longer using plastic connector for VTX and camera, just solder pads now; And bind and boot buttons reverted back to the original tiny ones

Specification:

(Frsky version) CRAZYBEE F4FR PRO V3.0 Firmware target: CrazybeeF4FR
(Flysky version) CRAZYBEE F4FS PRO V3.0 Firmware target: CrazybeeF4FS
(No RX version) CRAZYBEE F4 PRO V3.0 Firmware target: CrazybeeF4DX
MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: MPU-6000(SPI connection)
Board size: 28.5 * 28.5MM
Power supply: 2-4S battery input (DC 7-17V)
Built-in 10A(each) Blheli_S 4in1 ESC Dshot600 ready
Frsky version Built-in SPI Frsky receiver with telemetry(D8/D16 switchable)
Flysky version Built-in SPI Flysky receiver with telemetry(AFHDS/AFHDS2A switchable)
No RX version need to add external Receiver
Built-in Betaflight OSD(SPI Control)
Built-in Current meter Max 70A
Current meter scale set to 470
Built-in 5V 1A BEC
Built-in voltage detection

MCU upgraded to EFM8BB21
Power supply: 2-4S LiPo/LiPo HV (7v/17v)
Current: 10A continuous peak 12A (5 seconds)
Support BLHeliSuite programmable
Factory firmware: F_H_40_REV16_5.HEX
Default protocol: DSHOT600

SPI BUS receiver
Frsky D8/D16 switchable
Compatible Non EU transmitter both D8 and D16 mode
Channels: 8ch or 16ch
Failsafe support
No ground interference ( Transmitter and receiver 1 m from the ground): 300m

SPI BUS receiver
Protocol: AFHDS and AFHDS-2A Switchable
Channels: 8ch(AFHDS) or 14ch(AFHDS-2A)
No ground interference ( Transmitter and receiver 1 m from the ground): 300m
Failsafe support

No RX version support external serial-bus receiver like XM+, crossfire, S-FHSS etc.